Basic Info.
Product Description
Cable hanger instructions
Overview
The fully automatic cable hanger is a hand-held, free-to-height cable quick-bundling tool. It is equipped with components such as controllers inside, which can automatically complete all the steps of cable bundling. It can be widely used in the field of communication engineering to replace traditional labor. Attach the strapping cable. This machine is suitable for galvanized iron wire and coated wire. The machine is mainly composed of five parts: the body, the special reel, the battery, the remote control switch and the hand-held lever.
Technical Parameters
Battery capacity: 6600 mAh/group, one battery can work more than 800 times, probably attached to more than 3 kilometers.
Attached rod: can be insulated 10KV, the material is made of insulated FRP epoxy tube, 1.2 m / root.
Galvanized iron wire: 110 meters per plate, 300-700 mm at a time, each plate can be tied 150-180 times.
Coated iron wire: 100 meters per plate, 300-700 mm at a time, each plate can be tied 150-180 times.
Remote control switch: The remote control distance is 20 meters, which can be used separately.
Voltage: 12V Bundling range: 0-60mm Bundling time: 0.8 seconds each galvanized wire diameter: 0.8mm coated wire diameter: 0.85mm
Charging time: up to 3 hours
Instructions:
1. Remove the battery insulation rod and charge the lithium battery. The green light is on, and the charging time is about 3 hours. After the battery is fully charged, the host is turned on and the main switch is turned on. At this time, the buzzer will sound a beep. Indicates that the machine is powered.
2. Rotate and remove the round cover of the fixed cable tray in the middle of the fuselage, and then load the customized wire disc of our company into the set position.
3, take out a tray of wire and pull straight 10 cm, insert into the rectangular entrance hole of the fuselage, forward it to the bottom, install the cable tray, and rotate the dome to tight (if the wire is not straightened, It is easy to cause the wire, the wire can not enter the specified track).
4, boot, use the remote control to pull out the cable to test, the wire is sent out according to the specified track, to ensure the successful installation of the cable.
Warning: When the machine is working, the hand cannot touch the wire walkway to prevent personal injury.
5. Remove the properly insulated rod and the battery insulation rod for docking.
6. Lift the fuselage and choose the appropriate route for construction.
7. Put all the cables that need to be bundled into the binding groove.
8. The construction personnel press the remote control switch, and the attached machine automatically spins, hinges and cuts.
9. Press the second time after the operation, do not operate continuously several times, so as to avoid the two wires being wound together.
10. If you don't work for a long time, you will hear the continuous hum of the machine. Please restart the power and the machine will resume working.
11. Tie the aisle slider adjustment, first loosen the two screws with the tool, then adjust to the appropriate position (as shown below)
The direction of the needle gradually reduces the diameter of the circle formed by the filament, and vice versa.
Repair and maintenance
1. Ensure that the wire outlet is clean and free of foreign matter.
2, can not be placed at random, when idle, please load the original package.
3. Replace the loss parts (outlet pressure plate, wire cutter, etc.) in a timely manner.
4. During the use of the machine, the cover should be opened frequently to clean the motor and the end of the wire of the gear box to extend the service life of the machine.
Warranty content
This product has been warrantyed for six months from the date of purchase, and the battery warranty is three months. The charger, wire cutter and outlet plate are not covered by the warranty. Damage to the strapping machine due to man-made or natural disasters is not covered by the warranty.
Safe use of the code:
1. Please read the instructions carefully when using this product.
2, the strapping machine can not be placed at will, so as not to damage the internal parts, nor can you hit the machine head, otherwise it will cause partial wire.
3. The strapping machine cannot be stored in a humid environment. When not in use, it should be stored in a dry, clean, non-corrosive atmosphere.
4. When the machine buzzer sounds an alarm, the power must be turned off immediately, and the operation can be continued after the fault is eliminated.
5. The battery is strictly prohibited from being exposed to open flames, hot objects or directly exposed to rainy weather.
6. When charging, do not place in a humid or high temperature environment, and require charging with the specified charger.
7. The strapping machine should be stored in a place that children cannot touch to avoid injury.
8. When the strapping machine is working, the hand is forbidden to enter the part of the aisle walkway.
9. If you find that the battery is expanding, stop using it immediately and replace the battery.
10. When the strapping machine is idle for a long time, please unplug the battery.
11. The company is not responsible for the damage caused by the use of this product in accordance with the relevant operating and safety regulations of this manual.
12. Wear a helmet before using the machine.
Product failure repair Failure phenomenon
The strapping machine cannot be turned on
No response after pressing the key. 1. The battery is dead.
2, battery damage
3, poor line contact
4, line failure Replace the battery or charge, if it can not be opened, open the case to check the line or repair
When the remote control switch is pressed, the machine idles and there is no wire. 1. The wire is not silky.
2. When the wire disc is loaded, the wire head is not straightened. 1. Replace the wire disc.
2, remove the wire tray
3, straightening the bent wire head
Press the remote control switch, the machine does not work 1. The battery is low.
2. The gear part is stuck by foreign matter
3, the circuit board failure 1, the battery is charged
2. Open the gear part and take out the foreign object.
3, repair
The wire cannot be cut after the wire is cut. The tool is worn or the outlet plate is worn. Replace the tool or the outlet plate.
Press the remote control switch, only the wire is released, not bundled. 1. Hall element sensing position offset
2, Hall element damage
3. Line failure 1. Load the Hall element into the corresponding position.
2, replace the Hall element
3, repair
The charger LED is not lit and cannot be charged. The charger is faulty. Replace the charger.
Partial wire: When the wire is bundled, the wire arc cannot be tightened outside the jaw. When the wire is bundled, an object blocks the jaw to interfere with the wire track, causing the wire to be deflected. Adjusting the bundling angle and removing the foreign wire from the jaw wire.
Buzzer alarm 1. The power switch is turned on and left for more than one minute.
2. The battery is dead. 1. Turn off the power switch and turn it on again.
2, replace the battery
special attention items:
1. Use the last one meter of the wire disc. Be sure to pull the remaining wire together along the plastic wire disc. Do not use it directly or cut the wire. Otherwise, the machine channel will be blocked by the wire and it will not work. If the wire cannot be retracted, first check if the scissor head is tight. If the card is tightened with a diagonal pliers, the torsion shaft can be rotated several times to exit smoothly.
2. It may be normal to have a tightly wounded situation. In addition, the new battery has no power or insufficient power, and there is also a problem that the wire is not tight. Replace the fully charged battery and it will be eliminated. Please feel free to use it.
3. When using the new battery for the first time, first use up the battery power, and then fully charge it once, so that you can extend the battery life and better serve you.
4, 1 Forbidden to use in rainy days 2 Do not tie cables.
Standard configuration:
One cable binding machine, four 1.2-meter insulated rods, two remote controls, two sets of galvanized iron wire, two sets of battery packs, one charger, two inner hexagons, and one instruction manual.
